ABS-M30® for Fortus® — Specs, Test Results & 92ci Pricing
Looking for a Fortus®-class ABS-M30® workflow without closed-system markup? NEXT 3DP ABS is built around the fundamentals that drive repeatability on industrial Fortus® builds: 1.795 mm nominal diameter (Fortus®-class), controlled ovality, disciplined drying, moisture-managed packaging, and lot-traceable documentation. This page summarizes the workflow priorities plus a side-by-side comparison against Stratasys® ABS-M30® using ASTM test data.
Overview
In Fortus® production environments, ABS success is driven by workflow control: stable feeding, stable extrusion, and consistency across long builds. Outcomes are less about branding and more about dimensional control + conditioning + packaging integrity.
- Fortus®-class nominal filament diameter: 1.795 mm
- Diameter & ovality control for stable feed behavior
- Moisture discipline: dried prior to packaging + packaging stays dry until use
- 92ci reference: comparisons are clearest when normalized to Fortus® 92ci format
Practical takeaway Control the fundamentals and the printer behaves predictably — especially on longer Fortus® jobs where variability gets expensive.
Quick reference
Polymer family
ABS (Fortus® workflow)
Fortus®-class nominal diameter
1.795 mm
Packaging
Moisture-managed (sealed)
Pricing reference
92 in³ (1510cc)
Use the 92ci section below with your build volumes to estimate cost-per-part.
Specs that matter in Fortus® ABS production printing
In practice, the “make or break” factors are feed stability and consistency over time: correct nominal diameter (1.795 mm), controlled ovality, disciplined drying, and packaging that stays controlled until use.
Workflow control factors
- Fortus®-class nominal filament diameter: 1.795 mm
- Diameter & ovality control for stable feed behavior
- Dried prior to packaging (conditioning discipline)
- Moisture-managed packaging (stays controlled until installation)
Documentation & traceability
- Certificate of Analysis (COA)
- Certificate of Conformance (CoC)
- Lot traceability for repeat builds and controlled workflows
- Additional documentation may be available (program / application dependent)
NEXT 3DP ABS vs Stratasys® ABS-M30® — compatibility & workflow
NEXT 3DP ABS is positioned as a Fortus®-class ABS workflow alternative, focused on the same fundamentals: 1.795 mm nominal diameter, moisture control, and documentation for traceable production printing.
| Specification | NEXT 3DP | Stratasys® |
|---|---|---|
| Nominal diameter (Fortus®-class 1.795 mm) | ✓ | ✓ |
| Diameter & ovality control | ✓ | ✓ |
| Dried prior to packaging | ✓ | ✓ |
| Moisture-control insert / desiccant | ✓ | ✓ |
| Packaging format | Sealed barrier packaging | Canister system |
| Use case fit | Industrial fixtures + tooling | Industrial fixtures + tooling |
Tip: use the 92ci numbers below and convert to cost-per-part with the calculator to compare real geometry.
ASTM mechanical results (side-by-side)
| Tensile — ASTM D638-14 | ||
|---|---|---|
| Property | NEXT 3DP ABS | Stratasys® ABS-M30® |
| Modulus (MPa) | 2,150 | 2,220 |
| Tensile Yield (MPa) | 35.7 | 32.6 |
| Elongation at Yield (%) | 1.88 | 1.80 |
| Strain at Break (%) | 8.88 | 13.5 |
| Flexural — ASTM D790-17 | ||
|---|---|---|
| Property | NEXT 3DP | Stratasys® |
| Flexural Modulus (MPa) | 1,710 | 1,910 |
| Flexural Stress @ 5% | 54.0 | 55.1 |
| Impact — ASTM D256-10 | ||
|---|---|---|
| Test | NEXT 3DP | Stratasys® |
| Izod Unnotched (J/m) | 362 | 369 |
| Izod Notched (J/m) | 130 | 152 |
| Heat Deflection — ASTM D648-18 | ||
|---|---|---|
| Load | NEXT 3DP (°C) | Stratasys® (°C) |
| @ 66 psi | 102.8 | 99.6 |
| @ 264 psi | 98.0 | 93.9 |
Interpretation Measured differences should be evaluated relative to the functional requirement of the part. For many tooling and fixture applications, both materials fall within the same practical performance class.
ABS-M30® 92ci price comparison (USD)
In Fortus® material ecosystems, 92 cubic inches (92ci) is the standard reference format for pricing and comparisons. Use the calculator to convert part volume into cost-per-part.
| Material | Price (92ci) | Notes |
|---|---|---|
| Stratasys® ABS-M30® | $454 | Typical OEM reference pricing (92ci) |
| NEXT 3DP ABS | $125 | Save ~$329 (~72%) vs typical OEM 92ci context |
ABS-M30® FAQ (Fortus®)
What does “92ci” mean for Fortus® material pricing?
92ci (92 cubic inches) is the standard Fortus® reference format used to compare material costs consistently across suppliers. It’s a practical normalization point for cost-per-part calculations.
What filament diameter does Fortus® use for ABS-M30® workflows?
Fortus®-class materials in this workflow are commonly supplied at a nominal filament diameter of 1.795 mm. Diameter and ovality control are major drivers of feed stability on long builds.
How do I estimate ABS material cost per part?
Use the Fortus Material Cost Calculator to convert your part volume into cost-per-part using 92ci pricing context: open the calculator.
Is NEXT 3DP affiliated with Stratasys®?
No. NEXT 3DP is independently operated and not affiliated with or endorsed by Stratasys. OEM names are used for identification and compatibility context only.
Trademarks: Stratasys® and Fortus® are registered trademarks of Stratasys, Inc. NEXT 3DP is an independent supplier. OEM names are used for identification only.